Serial Nº Interface module: | Date: |
MENU | Parameter | Description | Adjusted Value | Unit |
ALRM | H2H | High H2 alarm | ppm | |
H2VH | Very high H2 alarm | ppm | ||
H2OH | High water content alarm | ppm | ||
H2OV | Very high water content alarm | ppm | ||
W20H | High water content at 20 °C alarm | ppm | ||
W20V | Very high water content at 20 °C alarm | ppm | ||
RSH | High relative saturation alarm | % | ||
RSVH | Very high relative saturation alarm | % | ||
H2T | High H2 trend alarm | dias | ||
H2OT | High water trend alarm | dias | ||
W20T | Water trend at 20 °C alarm | dias | ||
ALMH | Alarm hysteresis value | % |
CONF | BDR | Serial communication Baud-rate | Kbps | |
PRT | Communication protocol | |||
END | Address in RS-485 (to Modbus® protocol) | |||
END1 | Address 1st part in RS485 (to DNP3 protocol) | |||
END2 | Address 2st part in RS485 (to DNP3 protocol) | |||
DLTX | Data trasmition delay | ms | ||
DLRX | Data reciver delay | ms |
OIL | A1 | Constant A of water solubility, uniti and decimal | ||
A2 | Constant A of water solubility, hundredths | |||
B | Constant B of water solubility | |||
TREF | Reference Temperature | °C | ||
RSCL | Relative saturation calibration | % | ||
RSEP | Relative saturation limit aplication value | % | ||
RSNP | Relative saturation nominal point equals to the calibration | % | ||
TTCW | Water trend time constant | h | ||
FH2O | Filter rate of relative water and oil temperature |
H2 | H2CL | H2 calibration | ppm | |
TTCH | H2 trend time constant | |||
FLH2 | Filter rate of relative H2 | |||
LERN | Starts the H2 learning |
ADVC | CONF | DISP | Display mode | |||||||
NPWD | New password | |||||||||
LOG | TIME | LOG Recording time interval | min | |||||||
VARI | Variation in the measurements for recording purposes | % | ||||||||
RST | LOG Reset | |||||||||
RL1 | RL2 | RL3 | RL4 | |||||||
RLAY | RL | MODE | Logic of the relay Normal/Inverted (NC/NO) | |||||||
H2 | Define H2 alarms that activate the relay | |||||||||
H2O | Define H2O alarms that activate the relay | |||||||||
TRND | It associates the relay to trend alarms | |||||||||
DIAG | It associates the relay to self-diagnostic alarms | |||||||||
RDET | H2H | Triggers the relay by high H2 alarm | ||||||||
H2VH | Triggers the relay by very high H2 alarm | |||||||||
H2OH | Triggers the relay by high H2O alarm | |||||||||
H2OV | Triggers the relay by very high H2O alarm | |||||||||
W2OH | Triggers the relay by high H2O at 20 °C alarm | |||||||||
W20V | Triggers the relay by very high H2O at 20 °C alarm | |||||||||
RSH | Triggers the relay by high relative saturation | |||||||||
RSVH | Triggers the relay by very high relative saturation | |||||||||
H2TH | Triggers the relay by amount of days until reach a high H2 level | |||||||||
H2TV | Triggers the relay by amount of days until reach a very high H2 level | |||||||||
WTH | Triggers the relay by amount of days until reach a high H2O level | |||||||||
WTV | Triggers the relay by amount of days until reach a very high H2O level | |||||||||
20TH | Triggers the relay by amount of days until reach a high H2O level at 20 °C | |||||||||
20TV | Triggers the relay by amount of days until reach a very high H2O level at 20 °C | |||||||||
ANOU | AOR | Range of analog outputs | mA | |||||||
AV1 | Variable of analog output 1 | |||||||||
BOS1 | Beginning of the scale of analog output 1 | |||||||||
EOS1 | End of the scale of analog output 1 | |||||||||
AV2 | Variable of analog output 2 | |||||||||
BOS2 | Beginning of the scale of analog output 2 | |||||||||
EOS2 | End of the scale of analog output 2 | |||||||||
ANOT | ANO1 | Tests the analog output 1 | ||||||||
ANO2 | Tests the analog output 2 |
Was this article helpful?
That’s Great!
Thank you for your feedback
Sorry! We couldn't be helpful
Thank you for your feedback
Feedback sent
We appreciate your effort and will try to fix the article